Lumasense-technologies M330 Manual de usuario

MANUA LM330Blackbody Calibration Source

M330 Manual Introduction  102.4 Dimensions330M330 Front Panel

M330 Manual Introduction  11M330 Back Panel

M330 Manual Introduction  12To ensure consistent document formatting, this page was intentionally left blank.

M330 Manual Installation  133 InstallationInstall the blackbody emitter in the desired location that preferably has no moving air near theemitter ap

M330 Manual Installation  145. As the cavity flange approaches the furnace tube, very gently continue insertion untilthe cavity stops moving. It is

M330 Manual Operation  154 Operation4.1 Starting Up1. Allow the M330 to warm-up to room temperature for at least two hours afterunpacking and prior

M330 Manual Operation  164.2 Changing the SetpointPress either the UP/DWN buttons on the controller. Each press will advance the setpoint 1degree. T

M330 Manual Operation  174.4 Changing Temperature UnitsYou can select one of three temperature units: Celsius, Fahrenheit, and Kelvin.To change temp

M330 Manual Operation  184.5.2 RS485 OptionRS485 two wire is available as an option. The connection scheme is shown below:RS485 for multi-drop appl

M330 Manual Operation  194.6 PID Tuning ConstantsThe PID tuning constants have been factory set for optimum performance and are noted below.PID 1 PI

Confidential InformationThe material contained herein consists of information that is the property of LumaSenseTechnologies and intended solely for us

M330 Manual Operation  20To ensure consistent document formatting, this page was intentionally left blank.

M330 Manual Maintenance  215 Maintenance5.1 Cavity LifeThe life expectancy of the cavity depends on the time and temperature of operation. The highe

M330 Manual Maintenance  22To ensure consistent document formatting, this page was intentionally left blank.

M330 Manual Service  236 Service6.1 Controller Calibration (Adjustment)The M330 has a precision, thermocouplemonitoring the emitter temperature. Th

M330 Manual Service  242. Press 2.3. Press 4 until Level 3 appears.4. Press 4 until 3 appears. Wait.5. Press 1 until INPUT OPERS and Cust Lin 1 Page

M330 Manual Service  250-510°CPID1(PB1, Int1, Rate1)510-710°CPID2(PB2, Int2, Rate2)710-1380°CPID3(PB3, Int3, Rate3)1380-1750°C(end)PID4(PB4, Int4, R

M330 Manual Service  266.3.1 Primary Thermocouple Replacement Procedure1. Remove the screws holding the M330 front and rear panels.2. Lower the fron

M330 Manual Service  27Warning: Electrical Shock Hazard! This equipment is to be serviced by trainedpersonnel only.8. Replace with new thermocouple

M330 Manual Service  28To check which heating element is broken:1. Disconnect the AC power.2. Locate which heating element is broken. Disconnect on

M330 Manual Service  29To replace a heating element:To replace a heater, both thermocouples must be moved out of the way of the heaters. Thenthe to

M330 Manual Contents  iiiContents1 General Information ...

M330 Manual Service  305. Pull top cover with heaters AND the three insulation blocks up and out.6. Remove only the bad heating element by loosening

M330 Manual Service  3110. Replace straps.11. Replace main supply wires to end straps.Proper connection of electrical straps and clamps. Top view.

M330 Manual Service  326.5 Outer Tube ReplacementWarning: Electrical Shock Hazard! This equipment is to be serviced by trainedpersonnel only.1. Loos

M330 Manual Service  334. Remove (chip away) ceramic cement at this location with small hammer and screwdriver.5. Slide outer tube out of cavity. Re

M330 Manual Service  346.6 Field Modification for Low Heat RateWarning: Electrical Shock Hazard! This equipment is to be serviced by trainedpersonne

M330 Manual Service  35Top view of new Thermostat location.Rear of blackbodyFront of blackbody3. Move Transformer Primary tap from 230 VAC (H3) to 2

M330 Manual Service  36Warning: Electrical Shock Hazard! This equipment is to be serviced by trainedpersonnel only.4. Program M330 Controller accord

M330 Manual Service  371. Remove rear cover.2. Attach a Clamp-On Ammeter to one of the supply wires. This meter should measure TrueRMS current. Typi

M330 Manual Service  38To ensure consistent document formatting, this page was intentionally left blank.

M330 Manual Index  39IndexAAppropriate use 9BBaud Rate 17CCavity life 21Cleaning 21Controller Adjustment 23Controller Calibration 23DDimensions 10Di

M330 Manual Contents  iv6.3.2 Secondary Thermocouple Replacement Procedure... 276.4 Heater Element Replaceme

M330 Manual Index  40To ensure consistent document formatting, this page was intentionally left blank.

M330 Manual Appendix A: M330 Spectral Correction Procedure  41Appendix A: M330 Spectral CorrectionProcedure1. Set the M330 controller to the desired

M330 Manual Appendix A: M330 Spectral Correction Procedure  42950 948.1 943.2 940.9 937.3 933.9 935.4 935.7 942.1975 973.1 967.9 965.6 961.8 958.3 9

M330 Manual Appendix B: Optional Blackbody Spectral Radiance Correction Software  43Appendix B: Optional Blackbody SpectralRadiance Correction Soft

M330 Manual Appendix B: Optional Blackbody Spectral Radiance Correction Software  44To ensure consistent document formatting, this page was intenti

M330 Manual Appendix C: CE Certification  45Appendix C: CE Certification

M330 Manual General Information  51 General Information1.1 Information about the user manualCongratulations on choosing the high quality and highly

M330 Manual General Information  6 Do not attempt to operate with any of the safety features bypassed or disconnected. Do not place this unit wher

M330 Manual General Information  7Santa Clara, California Telephone: +1 408 727 1600 or +1 800 631 0176 Email: [email protected],

M330 Manual General Information  8To ensure consistent document formatting, this page was intentionally left blank.

M330 Manual Introduction  92 Introduction2.1 DescriptionThe M330 is a blackbody calibration source utilizing a digital indicating temperature contro