Lumasense-technologies 3434i SF6 Leak Detector Manual de usuario Pagina 188
- Pagina / 191
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 14
____________________________________________________________________
_____________________________________________________________________________
BE6028-14 3434i SF6 Leak Detector LumaSense Technologies A/S
Page 188 of 191
CLOCK SET TO DEFAULT ERROR
DETECTED IN CLOCK SETTINGS
The Monitor’s internal
clock was found to be
incorrectly set so these
values have been set to
their default values
A new battery has
been installed
FACTORS SET TO DEFAULT ERROR
DETECTED IN CALIBRATION
FACTORS
An error has been found in
the data stored in the
Calibration Factor part of
the Monitor’s memory, so
these factors have been
set to their default values
1. A defective
back-up battery
2. A defective
Working Memory
(RAM) or Source
Memory
(EEPROM)
3. A Software fault
MEMORY SET TO DEFAULT ERROR
DETECTED IN BACKGROUND MEMORY
An error has been detected
in the Monitor’s
Background Memory, so
the Monitor automatically
deletes all data stored in
this Memory
1. A defective
back-up battery
2. A defective
Working
memory ( RAM )
3. A software fault
MEMORY SET TO DEFAULT ERROR
DETECTED IN DISPLAY MEMORY
An error has been detected
in the Monitor’s Display
Memory, so the Monitor
automatically deletes all
data stored in this
memory.
1. A defective
back-up battery
2. A defective
Working Memory
( RAM )
3. A software fault
MEMORY SET TO DEFAULT ERROR
DETECTED IN INTERNAL MEMORY
An error has been found in
the data stored in the
Monitor’s internal memory.
data stored in this memory
cannot be read or altered
by the user, so the Monitor
automatically corrects any
errors found in this
memory
1. A defective
back-up battery
2. A defective
Working Memory
( RAM)
3. A software fault.
MEMORY SET TO DEFAULT ERROR
DETECTED IN SOURCE MEMORY
An error has been found in
the data stored in the
Monitor’s source memory,
so the Monitor
automatically gives stored
parameters default values.
1.
A defective
back-up battery
2. A defective
Source Memory
( EEPROM)
3. A software fault
PARAMETERS SET TO DEFAULT
ERROR DETECTED IN
CONFIG:/FORMAT PARAMETER
An error has been found in
the value parameters
stored in the Configuration
and/or Format branches of
the Monitor’s set-up tree,
and therefore the Monitor
has automatically given
these parameters default
values
1. A defective
back-up battery.
2. A defective
Working Memory
(RAM)
3. A software fault.
PARAMETERS SET TO DEFAULT
ERROR DETECTED IN THE TASK
SET_UP PARAMETER
An error has been found in
the value parameter stored
in the Monitoring Task
branch of the Monitor’s
set-up tree, and has
automatically given these
parameters default values.
1. A defective
back-up battery
2. A defective
Working Memory
(RAM)
3. A software fault.
- Instruction 1
- Safety Considerations 4
- Warnings! 6
- Applying Power 7
- 1.1 Introduction 9
- 1.2 Online Monitoring 9
- 1.5 Stand-alone Use 9
- Chapter 1 10
- Chapter 2 12
- Parameters 18
- Options 19
- 2.6 Setting-up user Levels 23
- 2.6.2 Changing the Password 24
- ↵ to change value 24
- Chapter 3 26
- 3.1 PC Use – Online 27
- 3.2 Stand-alone Use 28
- Chapter 4 30
- 4.1 Special Terminology 31
- 4.1.2 Monitoring Task 32
- 4.1.3 Sampling Interval 32
- 4.1.4 Continuous Sampling 33
- 4.1.5 Monitoring Period 33
- 4.3.2 Setting Units 37
- Page 42 of 191 42
- PRESS ENTER TO CHANGE VALUE 42
- MEASUREMENT IN PROGRESS 45
- Chapter 5 56
- 5.1 Introduction 57
- 5.2 Front Panel 57
- 5.2.3 Function Push-buttons 59
- 5.3.1 Introduction 61
- Front Panel 63
- 5.4 Configuring the Monitor 64
- 5.5 Alarm Relay 67
- Alarm Relay 1: 68
- Alarm Relay 2: 68
- 5.6 Continuous Warm System 69
- Chapter 6 70
- 6.1 Types of Parameters 71
- Chapter 7 74
- 7.1 The Parameters’ Units 75
- Normalization Temperature 76
- Sampling: 77
- Alarm set-up: 80
- Page 81 of 191 81
- Chapter 8 90
- Common Marks: 98
- Gas Marks: 98
- Other Marks Used: 99
- Chapter 9 100
- 9.1.3 Working Memory (RAM) 104
- Block 4 – Measurement Data: 105
- Software 115
- Chapter 10 116
- 10.1 Introduction 117
- 10.2 Printer Cables 117
- 10.3.1 RS-232 Interface 118
- 10.3.2 Ethernet Interface 120
- 10.5 Data Logging Function 124
- 10.6 Error Logging Function 124
- 10.7.1 Starting a Print-out 125
- PRINT ABORTING 125
- PLEASE WAIT 125
- Chapter 11 126
- Chapter 12 134
- Cell Noise 136
- Presence of Water Vapour 137
- Monitor 138
- Stand-alone Use 138
- 12.6 Zero-point Calibration 151
- RESULTS NOT YET AVAILABLE 154
- AND PRESS ENTER WHEN READY 157
- 12.8 Span Calibration 159
- Choosing a filter bank 160
- Chapter 13 177
- Chapter 14 185
- Warning and Error Messages 187
Relacionado con productos y manuales para Herramientas Lumasense-technologies 3434i SF6 Leak Detector
(199 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales