Lumasense-technologies M390 Manual de usuario

MANUA LM390Blackbody Calibration Source

M390 Manual Introduction  102.2 Technical DataThisModelModel Part No. Exit Aperture Temperature Range Power[ ] M390-A1 14029-A1 0.625 in 600-

M390 Manual Installation  113 Installation3.1 Installing the M390To install the M390:1. Allow the M390 to warm-up to room temperature for at least 2

M390 Manual Installation  12To ensure consistent document formatting, this page was intentionally left blank.

M390 Manual Operation  134 Operation4.1 Starting UpTo start up the M390:1. Turn on the power switch/breaker and allow 20 seconds for the system to s

M390 Manual Operation  14Eurotherm controller4.2.1 Other Controller ModesIf, for some reason, the power must be turned off while monitoring temperat

M390 Manual Operation  158. Press the UP button to set new units °F (or K for Kelvin, if desired). Confirm the changewith the RETURN button or press

M390 Manual Operation  164.5.1 RS485 OptionRS485 two wire is available as an option. The connection scheme is shown below:RS485 for multi-drop appl

M390 Manual Operation  174.6 PID Tuning ConstantsThe PID tuning constants have been factory set for optimum performance and are noted below.Heating

M390 Manual Operation  18Typical Radiance temperature calibration look-up table (LUT) used in our blackbodyTo gain access to the custom look-up tabl

M390 Manual Operation  19Note: Calibration points do not have to be used as pre-programmed. To dial in adifferent calibration point, simply change a

Confidential InformationThe material contained herein consists of information that is the property of LumaSenseTechnologies and intended solely for us

M390 Manual Operation  20To ensure consistent document formatting, this page was intentionally left blank.

M390 Manual Maintenance  215 Maintenance5.1 Cavity LifeThe life expectancy of the graphite cavity depends on the time and temperature of operation.T

M390 Manual Maintenance  225.4 Furnace Core DisassemblyThe graphite core can be replaced without disconnecting cooling or purge tubing. Refer toexpl

M390 Manual Maintenance  235.5 Fuse LocationsThe M390 has several fuses. Refer to the table below. See the appendix for photo-view of fuselocations

M390 Manual Maintenance  245.6 Recommended Spare PartsModelTemperatureRange Cavity LengthReplacementCavity KitQuartz Tube, ElectrodeSeats, and O-Rin

M390 Manual Troubleshooting  256 TroubleshootingSymptom Tests/ Solutions1. Blackbody Does not heat up Is there both Argon purge gas and coolingwater

M390 Manual Troubleshooting  269. Blackbody heats up and is glowing, butthe controller does not indicate temperature> beginning of range.Check th

M390 Manual Appendix A: Drawings  27Appendix A: Drawings

M390 Manual Appendix A: Drawings  28

M390 Manual Appendix B: ASCII/BASIC  29Appendix B: ASCII/BASICTypical ASCII request string to read the blackbody temperature:'-------make a req

M390 Manual Contents  iiiContents1 General Information ...

M390 Manual Appendix B: ASCII/BASIC  30A simple BASIC program to send blackbody setpoint:CLS'-----open comm port 1 for 9600 baud, 7,E,1-----OPE

M390 Manual Appendix C: Declaration of Conformance  31Appendix C: Declaration of Conformance

M390 Manual Appendix C: Declaration of Conformance  32To ensure consistent document formatting, this page was intentionally left blank.

M390 Manual Index  33IndexCCavity life 21Cleaning 24Controller Calibration 17Controller Modes 14DDisposal 7EEurotherm iTools Software 17FFurnace Cor

M390 Manual Index  34To ensure consistent document formatting, this page was intentionally left blank.

M390 Manual Index  35

M390 Manual Contents  iv6 Troubleshooting ...

M390 Manual General Information  51 General Information1.1 Information about the user manualCongratulations on choosing the high quality and highly

M390 Manual General Information  6Warning: DO NOT USE NITROGEN (N2) FOR PURGE GAS. AT HIGH TEMPERATURES,CYNIDE GAS COULD BE GENERATED.1.3 Limit of L

M390 Manual General Information  7Return the instrument upon receipt of the RMA nµmber, transportation prepaid. Clearlyindicate the assigned RMA nµm

M390 Manual General Information  8To ensure consistent document formatting, this page was intentionally left blank.

M390 Manual Introduction  92 Introduction2.1 DescriptionThe M390 series are high temperature blackbody calibrators that can produce a very hightempe