Lumasense-technologies M390 Manual de usuario Pagina 25
- Pagina / 35
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
M390 Manual Troubleshooting 25
6 Troubleshooting
Symptom Tests/ Solutions
1. Blackbody Does not heat up Is there both Argon purge gas and cooling
water flowing?
Are both low flow alarms off?
2. Blackbody Does not heat up-flow alarms
are off
Put the controller in MANUAL mode. Set to
approximately 20% power. Do you hear SCR
buzzing?
Yes: Wait until the controller reads
temperature above the beginning of the
temperature range. (either 250 C or 600 C)
Go to steps 3 to 7.
No: Check Low Flow alarms are working by
turning off cooling water supply for a few
seconds. Alarm should sound. Repeat with
Argon purge. Alarm should sound. Go to
step 7.
3. Answer to (2) is Yes: Blackbody Does not
heat up-flow alarms are off. Alarms test OK.
Check the over temperature thermal cut-out
switch located on the reflector plate just
under the blackbody cavity. This is a white
(ceramic) disc with a manual reset push
button. Push this button in if it has tripped.
This opens the 4-20 ma control signal to the
SCR.
4. Blackbody Does not heat up-flow alarms
are off. Alarms test OK. Over temp switch
OK.
Cavity may be open or damaged. Apply
more power in Manual mode. Set power to
about 40%. Look inside the cavity opening
for signs of local heating in unsymmetrical
patterns.
5. (4) above showed no signs of
unsymmetrical heating patterns and there is
no glowing anywhere in the cavity.
With power set at about 30% in Manual
mode, measure AC volts across the two
cavity electrodes.
If Velectrodes >2 VAC, cavity not connected
at one or both electrode seats.
6. If V electrodes = 0 VAC Check SCR main fuse. Check 4-20 ma
connector to SCR. Check 4-20 ma signal to
SCR from temperature controller.
7. If V electrodes > 0 VAC. Still do not
observe any glowing on cavity.
Cavity must be open. Shut system down and
replace cavity.
8. Blackbody heats up, but does not control
temperature.
Check that controller has been set to AUTO
mode after the blackbody temperature >
beginning of temperature range.
- Blackbody Calibration Source 1
- Contents 3
- M390 Manual Contents iv 4
- 1 General Information 5
- 1.4 Unpacking the Instrument 6
- 2 Introduction 9
- 2.2 Technical Data 10
- 3 Installation 11
- 4 Operation 13
- 4.3 Shutting Down 14
- M390 Manual Operation 15 15
- 4.5.1 RS485 Option 16
- 4.6 PID Tuning Constants 17
- 4.7 Controller Calibration 17
- M390 Manual Operation 18 18
- M390 Manual Operation 19 19
- M390 Manual Operation 20 20
- 5 Maintenance 21
- 5.4 Furnace Core Disassembly 22
- 5.5 Fuse Locations 23
- 5.6 Recommended Spare Parts 24
- 5.7 Cleaning 24
- 6 Troubleshooting 25
- Appendix A: Drawings 27
- Appendix B: ASCII/BASIC 29
- M390 Manual Index 33 33
- M390 Manual Index 34 34
- M390 Manual Index 35 35
Relacionado con productos y manuales para Herramientas Lumasense-technologies M390
(90 paginas)
(12 paginas)Fujitsu S26361-K902-V150 manuels
Manuels d'utilisation et guides de l'utilisateur pour Affichages LED Fujitsu S26361-K902-V150.
Nous fournissons des manuels en pdf 1 Fujitsu S26361-K902-V150 à télécharger gratuitement par type de document : Fiche technique
Comentarios a estos manuales