Lumasense-technologies IS 12-TSP Manual de usuario descargar pdf (Pagina 23)

IMPAC pyrometers IS 12-TSP · IGA 12-TSP

Reading temperature

value repeated:

AAmsXXX XXX = 000…999 (XXX = number of measuring values)

Reading basic tempera-

ture range:

AAmb Output: XXXXYYYY (hex 8-digit, °C or °F)

XXXX = beginning of temp. range

YYYY = end of temp. range

Reading temperature

sub range:

AAme Same as mb

Reading emissivity: AAem Output: XXXX (dec. 0010 … 1000 in ‰)

Emissivity: AAemXX XX = (10…99%), 00 = 100% (decimal)

Emissivity: AAemXXXX XXXX = (0010 … 1000‰) (decimal)

Exposure time t

: AAezX X = 0 ... 6 (decimal) 0 = intrinsic time constant of the device

1 = 0.01 s 3 = 0.25 s 5 = 3.00 s

2 = 0.05 s 4 = 1.00 s 6 = 10.00 s

External deletion: AAlx

Simulation of an external deletion contact

Clear time of maximum

value storage:

AAlzX *

)

X = 0 ... 8 (dec.) 0 = Maximum value storage off

1 = 0.01 s 4 = 1.00 s 7 = external deletion

2 = 0.05 s 5 = 5.00 s 8 = automatic deletion

3 = 0.25 s 6 = 25.00 s 9 = hold

Setting of temperature

sub range:

AAm1XXXXYYYY XXXX (hex 4-digit) beginning of temp. range (°C)

YYYY (hex 4-digit) end of temp. range (°C)

Analog output: AAasX *

)

X = 0 or 1 0 = 0...20 mA 1 = 4...20 mA

Limit contact 1: AAs1XXXX

XXXX = switch point limit contact 1

(ASCII-hex, 4 digit, full degree in °C or °F)

Limit contact 2: AAs2XXXX

XXXX = switch point limit contact 2

(ASCII-hex, 4 digit, full degree in °C or °F)

Setting hysteresis limit

contacts:

AAhlXX

XX = 2 … 20, full degree in °C or °F

Changing °C / °F AAfhX *

)

Output: X = 0: display in °C; X = 1: display in °F

interface type: AAin

Output: X = 1 or 2; 1 = RS232, 2 = RS485

Address: AAgaXX *

)

XX = (00 ... 97)

00 ... 97 = regular device addresses

99 = global address with response

98 = global address without response (only setting commands!)

Baud rate: AAbrX *

)

X = 1...6 or 8 (decimal)

1 = 2400 Baud 4 = 19200 Baud (7 is not allowed)

2 = 4800 Baud 5 = 38400 Baud 8 = 115200 Baud

3 = 9600 Baud 6 = 57600 Baud

Wait time: AAtwXX *

)

XX = 00 ... 99 (decimal)

Error status: AAfs Output: XX; XX=00…FF (00 = no error)

(01…FF: error code for LumaSense service)

Lock keyboard: AAlkX

X = 0 ... 3

1 = lock lk1, removal with command lk0 or power off-on

0 = removal of lock lk1

3 = continuous lock lk3, removal only with command lk2

2 = removal of lock lk3

Reading parameters: AApa Output decimal 11-digit:

Digit 1 und 2 (10...99 or 00):  (emissivity)

Digit 3 (0 ... 6): t

(exposure time)

Digit 4 (0 ... 8): t

(max. value storage clear mode)

Digit 5 (0 ... 1): analog output

Digit 6 und 7: (00 ... 98): temperature

Digit 8 und 9 (00 ... 97): address

Digit 10 (0 ... 6 or 8): baud rate

Digit 11 (0): always 0

Laser targeting light: AAlaX *

)

X = 0 switch off laser

X = 1 switch on laser

Internal temperature: AAgt

Output: XXX (dec. 000 ... 098°C or 032 ... 208°F)

Max. internal temp.: AAtm Output: XXX (dec. 000 ... 098°C or 032 ... 208°F)

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 51 52

Comentarios a estos manuales

Sin comentarios

Lumasense-technologies IS 12-TSP Manual de usuario Pagina 23

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Lumasense-technologies IS 12-TSP